The Mastermorphix Steps


The Mastermorphix will be solved layer by layer, and the algorithms are derived from those of the 3x3x3.

Step 1

The 1st Layer

When the layer is fully solved, your cube will look like this:

No specific algorithm.

The placement of the pieces should remain intuitive.

Here are the main steps:

The Centers

The Edges

The Corners

Step 1 bis

The Centers of the 2nd Layer


You must ensure that all centers are correctly oriented; if so, everything is fine.

Otherwise, you have 3 cases for each incorrectly oriented center.

Place the centers to be oriented as shown opposite.

When all the centers are correctly oriented, your cube will look like this:

Half turn

Quarter turn counterclockwise

Quarter turn clockwise

Step 2

The edges of the 2nd layer

When all the edges have been processed, your cube will look like this:

Place the edges - case 1-a
(1st set)

The edge to be placed is on the 3rd layer

It is on the right

The algorithm allows it to be placed on the 2nd layer.

Place the edges - case 1-b
(1st series)

The edge to be placed is on the 3rd layer

It is opposite

The algorithm allows it to be placed on the 2nd layer.

Place the edges - case 1-c
(1st series)

The edge to be placed is on the 2nd layer

It is incorrectly oriented

The algorithm allows it to be moved down to the 3rd layer and then put back in place, but correctly oriented.

Place the edges - case 2-a
(2nd series)

The edge to be placed is on the 3rd layer

It is on the right

The algorithm allows it to be placed on the 2nd layer.

Place the edges - case 2-b
(2nd series)

The edge to be placed is on the 3rd layer

It is opposite

The algorithm allows it to be placed on the 2nd layer.

Place the edges - case 2-c
(2nd series)

The edge to be placed is on the 2nd layer

It is incorrectly oriented

The algorithm allows you to move it down to the 3rd layer and then put it back in place, but correctly oriented.

Step 3.1

Orienting the edges of the 3rd layer

When all the edges have been processed, your cube will look like this:

Orienting the edges - case a

2 edges are correctly oriented

They are adjacent

The algorithm will orient the Front/Right edges and place them respectively in Back/Front.

Orienting the edges - case b

2 edges are correctly oriented

They are opposite

This formula will orient the Left/Right edges and place them respectively in Front/Right.

Orienting the edges - case c

No edges are correctly oriented

The algorithm will orient all the edges.

Step 3.2

Placement of the 3rd layer edges

When all the edges have been processed, your cube will look like this:

Place the edges - case 1-a
(1st set)

2 edges are correctly placed

They are adjacent

The algorithm will place the Left/Front edges.

Place the edges - case 1-b
(1st set)

2 edges are correctly placed

They are opposite

This formula will place the Front/Back edges.

Place edges - case 2-a
(mix 1st and 2nd series)

2 edges are correctly placed

They are adjacent

The algorithm will place the Left/Front edges.

Place edges - case 2-b
(mix 1st and 2nd series)

2 edges are correctly placed

They are opposite

This formula will place the Front/Back edges.

Place edges - case 3-a
(2nd series)

2 edges are correctly placed

They are adjacent

The algorithm will place the Left/Front edges.

Place the edges - case 3-b
(2nd set)

2 edges are correctly placed

They are opposite

This formula will place the Front/Back edges.

Step 4

The corners of the 3rd layer

When all the corners have been processed, your cube will look like this:

Place the corners - case 1-a
(1st set only)

The algorithm will swap the corners (except the one in front of you on the right) clockwise.

Depending on your setup, you should apply the algorithm a maximum of 2 times!!!

The orientation of the corners can vary. What matters is the placement.

Place the corners - case 1-b
(1st set only)

The algorithm will swap the corners (except the one in front of you on the left) counterclockwise.

Depending on your setup, you should apply the algorithm a maximum of 2 times!

The orientation of the corners can vary. What matters is the placement.

Orient the corners - case 1
(1st set only)

The algorithm will allow you to orient the two corners on your right upwards.


Depending on your setup, you should apply the algorithm a maximum of 2 times!

Remember to orient your cube correctly to avoid performing the algorithm more than necessary, i.e., not necessarily with the 3rd layer at the top.

Place the corners - case 2-a
(mix 1st and 2nd sets)

The algorithm will swap the corners (except the one in front of you on the right) clockwise.

Depending on your setup, you should apply the algorithm a maximum of 2 times!

The orientation of the corners can vary. What matters is the placement.

Place the corners - case 2-b
(mix 1st and 2nd sets)

The algorithm will swap the corners (except the one in front of you on the left) counterclockwise.

Depending on your setup, you should apply the algorithm a maximum of 2 times!!!

The orientation of the corners can vary. What matters is the placement.

Orienting the corners - case 2
(mix of 1st and 2nd sets)

The algorithm will allow you to orient the two rightmost corners upwards.


Depending on your setup, you should apply the algorithm a maximum of 2 times!!!

Remember to orient your cube correctly so as not to perform the algorithm more than necessary, i.e., not necessarily with the 3rd layer at the top.

Step 5

The center of the third layer

When the center is correctly oriented, your cube will look like this:

U-turn


Your Mastermorphix is solved.