The Fisher Puzzle Steps


The Fisher Puzzle is solved layer by layer, and the algorithms are derived from those of the 3x3x3.

Step 1

The 1st Layer

When the layer is fully solved, your cube will look like this:

No specific algorithm.

The placement of the pieces should remain intuitive.

Here are the main steps:

The Centers

The Edges

The Corners

Step 1 bis

The Centers of the 2nd Layer


You must ensure that all centers are correctly oriented; if so, everything is fine.

Otherwise, you have 3 cases for each incorrectly oriented center.

Place the centers to be oriented as shown opposite.

When all centers are correctly oriented, your cube will look like this:

Half turn

Quarter turn counterclockwise

Quarter turn clockwise

Step 2

Edges of the 2nd layer

When all edges have been treated, your cube will look like this:

Note: we do not know if the edges are correctly oriented; therefore, there is no case c and step 2 bis may be necessary.

Place the edges - case a

The edge to be placed is on the 3rd layer

It is on the right

The algorithm allows it to be placed on the 2nd layer.

Place the edges - case b

The edge to be placed is on the 3rd layer

It is opposite

The algorithm allows it to be placed on the 2nd layer.

Step 2 bis

Parity of the edges of the 2nd layer

The number of misoriented edges in the 3rd layer must be even (0, 2, or 4). If this is the case, everything is fine.

Otherwise, if it's odd, an edge in the 2nd layer is misoriented; you have two scenarios (for 1 or for 3).

Position the misoriented edges as shown opposite.

When the number of edges in the 3rd layer is even, you will have one of the following four scenarios:

Handle edge parity

1 misoriented edge

The algorithm will orient one edge.

Handle edge parity

3 misoriented edges

The algorithm will orient one edge.

Step 3.1

Orientation of the edges in the 3rd layer

When all edges have been processed, your cube will look like this:

Orienting edges - case a

2 edges are correctly oriented

They are adjacent

The algorithm will orient the Front/Right edges.

Orienting edges - case b

2 edges are correctly oriented

They are opposite

This formula will orient the Left/Right edges.

Orienting edges - case c

No edges are correctly oriented

The algorithm will orient all edges.

Step 3.2

Placement of the 3rd layer edges

When all the edges have been processed, your cube will look like this:

Place the edges - case a

2 edges are correctly placed

They are adjacent

The algorithm will place the Left/Front edges.

Place the edges - case b

2 edges are correctly placed

They are opposite

This formula will place the Front/Back edges.

Step 4

The corners of the 3rd layer

When all the corners have been processed, your cube will look like this:

Place the corners - case a

The algorithm will swap the corners (except the one in front of you on the right) clockwise.

Depending on your setup, you should apply the algorithm a maximum of 2 times!

L'orientation des coins peut varier. Ce qui compte, c'est l'emplacement.

(Les 2 couleurs de chaque coin doivent correspondre aux 3 faces théoriques du coin)

Placer les coins - cas b

L'algorithme va permuter les coins (sauf celui placé devant vous à gauche) dans le sens inverse d'une aiguille d'une montre.

Selon votre configuration, vous devriez appliquer l'algorithme 2 fois maximum !!!

L'orientation des coins peut varier. Ce qui compte, c'est l'emplacement.

(Les 2 couleurs de chaque coin doivent correspondre aux 3 faces théoriques du coin)

Orienter les coins

L'algorithme va vous permettre d'orienter vers le haut, les 2 coins de votre droite.


Selon votre configuration, vous devriez appliquer l'algorithme 2 fois maximum !!!

Remember to orient your cube correctly to avoid running the algorithm more than necessary, i.e., not necessarily with the 3rd layer at the top.


Your Fisher puzzle is solved.